for raspberry pi5  
  data storage - PCIe to dual 2.5" SATA HDD Shield  
     
 
  Home       Be Our Distributor      Custom Products      OEM/ODM      What We Do      Contact  
     
 
  X1007 V1.1  ACTIVE hardware   software  
     
     
     
     
       Product Overview  
 
 

Introducing the X1007 PCIe to 2 ports SATA HDD/SSD expansion board, designed to provide a mass-capacity storage and high-speed storage solution for your Raspberry Pi 5. This board facilitates the simultaneous connection of two 2.5-inch HDDs/SSDs, unleashing the full potential of your storage capabilities, with SATA 3.0 interface speeds reaching up to 5Gbps.

The X1007 connects to the underside of the Raspberry Pi 5, eliminating the need for a passthrough for the GPIO. This means you can use your favorite HATs while also utilizing this expansion board. Additionally, the X1007 and your HDDs can be powered from Raspberry Pi5 via pogo pins, streamlining the power supply to a single source.

The X1007 serves as the perfect storage solution for establishing a home media center or constructing a network-attached storage (NAS) system. It empowers you to store and stream your personal collection of videos, music, and digital photos within the confines of your home or remotely from anywhere around the globe..

 
 
       Product Features  
 
 

Compatible With
- Raspberry Pi 5B

 

- Supports the connection of two 2.5-inch HDD/SSD to your Raspberry Pi 5 simultaneously

- Supports up to 4TB + 4TB 2.5-inch SATA disk drives (HDDs/SSDs)
- Compliant with the Serial ATA 3.0 specification, with backward compatibility to SATA 2.0 and SATA 1.0
- Adheres to the PCI-Express v2.0 specification and is backward compatible with PCI-Express v1.0
- Supports communication speeds of 5.0 Gbit/s, 3.0 Gbit/s, and 1.5 Gbit/s
- Compatible with SATA 6G, 3G, and 1.5G hard drives
- Features plug-and-play installation for ease of setup
- LED indicators display power and drive status
- Powered from Raspberry Pi5 via pogo pins, streamlining the power supply to a single source
- Compatible with the official active cooler without compromising cooling performance
- Supports the HAT+ STANDBY power state, automatically turning off SATA devices when the Pi 5 is powered down

 

*The X1007 is designed for data storage purposes and does not currently support booting from HDD/SSD with the existing firmware.

 
       Test & Reviews  
 
 

Test Conditions

-System board details: Raspberry Pi 5 Model B Rev 1.0 , 4G RAM

-Interface board details: X1007 v1.1 PCIe to dual 2.5" SATA HDD/SSD Shield

-Operation system: Raspberry Pi OS with desktop (Debian12 (bookworm), 64bit, Release date: December 5th 2023)

-Storage details: Samsung EVO 750 SSD, HITACHI Travelstar Z7K500 500G HDD

 

Testing disk drives read speed at PCIe2.0 with hdparm

 

 

Samsung EVO SSD: 430.69MB/s, HITACHI Travelstar HDD: 123.05MB/s

 
       Technical Specification  
 
 
Power supply : 5dc +/-5%  ≥3A via FFC & pogo pins
Ports & Connectors : PCIe connector x1 - 16-pin pitch0.5mm
  SATA connectors x2 - 7+15P
PCIe FFC cable length : 37mm
PCB Size : 164.5mm x 71.85mm
 
       Package Contents  
 
 

- X1007 V1.1 PCIe to dual 2.5" SATA  HDD shield x1

  - PCIe FFC 37mm x1
  - Screw pack x1 
 
        Important Notes  
 
 
- The X1007 is designed for data storage purposes and does not currently support booting from HDD/SSD with the existing firmware.
- Older SATA drives with less efficient flash media may not perform as well as newer drives
- New SATA HDDs/SSDs are not partitioned and will need to be both partitioned and formatted when first connected to the Raspberry Pi before they will be accessed in the Explorer.
 
 
   
   
© 2024 SupTronics Technologies Limited, All Rights Reserved.